I do videos as a reminder to myself, but info might be of use to others too. Did this one a few minutes ago. Often I hop from one thing to another so fast that I can't remember how I did something. Usually I can figure it out if a simple technique was used, but when I use many products, have many layers, I forget. There are many such examples around my studio that I would love to try and recreate, but have forgotten what I did. Sound familiar? Anyway, I love this veneer and definitely want to do it again, maybe altering some things, so this video will help me, hope you get some value from it as well:
Here are some other shots of the veneer, including one that shows how translucent it is.
I have one little issue and may have to experiment. If I flip veneer over when applying it to base (bead or whatever), colors would be protected, and then I could sand and polish to get a nice sheen, however, wondering whether the last layers (white) would not show up at all. So I will have to try it. more on the results later.
Here are some quick, unedited videos of the results of my experiments so far using these products:
Golden Special Iridescent Acrylics - Pearl Mica Flake
Golden Heavy Body Artist Acrylics - Iridescent Gold Mica Flake (Large)
Black Mica Flake small
Here are unedited (sorry), videos showing some experiments using these products.
They are rather pricey and I am pretty sure you canake your own cheaper, just use a gel medium, and add Mica Flakes (which i have seen on Etsy for about $3.00 and glitter.
I have admired a beaded necklace for some time and decided I would try to use it as inspiration for a polymer clay version. This is my first attempt, I have a few things I might do differently if I attempt to do this again. I really love the colors.
Good thing I have a sense of humor, because I should not be proud of such a mess, but it does make me giggle when I look at it, also, "maybe" I can get some of it cleaned up, well maybe?
WARNING: Do not watch this video if you hate bad camera work.
I am not competent enough to edit it so you wouldn't get dizzy, but since project has been completed, I cannot redo it.
Comments: I keep calling it Peel and Stick, but it really is Glad "Press and Seal"
that I am using. I also gave info on the Tim Holtz palette.
I had camera and paper towel in one hand, and was painting, etc with other, so not the best method. But I offer it so that you can see what I did. If you want to skip the video, here are my steps
1. Bought palette after experimenting using found packaging to dry alcohol inks and liked it
Eliminates most of the mess and potential accidents associated with using alcohol inks. See my blog posting here.
2. Did not like that I couldn't identify colors once inks were dried on palette.
3. Also wanted to see what the colors looked like when applied to white polymer clay
4. Squirted my inks into receptacles in palette
5. Kept record of which inks were where in palette
6. Made raw white (Souffle) clay disks and placed them on the Press and Seal in exact placement as inks on palette.
7. Using my brush pens (see blog posting on these here) (Honbay 3pc water Brush Watercolors Pens Art Painting Brushes} I added color from ink palette reservoirs to each clay disk, as indicated on my paper record. 8. Let them dry, then faced with a dilemma, I wanted to cover these disks with the Press and Seal, but was afraid it would lift the color off of the disks (I ultimately discovered it would), so I covered each disk first with UV Resin and cured in sunlight on the raw clay (Note: the cured UV Resin can be put in oven at regular Polymer clay temps, so If later I want to cure the polymer clay disks, I can--added benefit is the cured UV resin should protect the color of the inks before and after curing the PC:
9. Worked perfectly, UV resin hardened in sunlight, and did not stick when covered by press and seal.
10. Lastly, I used my Silhouette Cameo and a pen inserted into holder to make teeny tiny labels from full page labels (I use this often, see posts here and here, and here
So now I have project done. I have found that the colored disks protected with Press n Seal, fits inside the palette (Note, let any inks you have used completely dry before trying to put the samples on top and closing palette), here are a few pics of how that works.
After each disk covered with UV Resin (outdoor pic)
Disks labeled uncovered:
Disks covered and stored on top of the inks in palette with lid closed:
So samples are always with the palette, and I know how they look on white polymer clay, and I know the name and source of the inks for when I run out. I must say that using the brush pens and dried alcohol inks, they last a very, very, long time and go very far. Also, I have some plastic clear bags, or packaging material and apply color to that often squeeze more alcohol to make less intense if that is what I am going for. You can squeeze alcohol onto the clay and move ink around too, but you might get too much alcohol onto your clay. Here are some projects I have recently made using these inks. (I did recently get the metallic additives too), but have not tried to dry those on palette yet:
In late March I was watching Kalyana live tutorial, cannot now remember which specific one, however. I learn so many tips watching these. In one she demonstrated the Stroppel Cane and made into veneer then used in a cuff bracelet. I was inspired to try one myself with a scrap cane. When slicing, I decided to align the slices in opposite alignment more like a basket weave. Here is a picture showing the cane block, the veneer and a pair of earrings made from the veneer.
In the process of making the video in the last post, I jury-rigged a setup to get a nice closeup of the project. I used what I had, just setting my eyes on things around me. turns out the video turned out pretty good, I do like closeups of work. I used my phone's camera (I have a MotoZ Play phone) and when I borrowed my husband's phone, I decided to reveal the setup. So if you all have anything to share and want to do a quick video, just look around you. Good window light is quite important. See following video where I showed (behind the scenes, lol) recording of the video I posted yesterday:
It has been a very long time since posting, I have gone back to an old hobby of mine and have learned new tricks. One thing I have been able to do is crossover many of my skills/techniques to almost all of the hobbies. Making Polymer Clay jewelry has been more fun for me this time around. I am also finding new ways to apply my old skills to Polymer Clay. Most recently, similar to making labels on my Silhouette Studio Cameo by sketching outlines in black, then painting them in as I need them, as I did here, and here. So now I am using similar approach with my polymer clay, silkscreen designs on raw clay, let dry, then apply color as needed using alcohol inks and Inktense blocks:
Here is a video showing that process:
